recover dead kathrein 910

[Ники]

Requirements:
¦Nullmodemcabel and existing com port on your PC / laptop
¦Crossover cable
¦Hyperterminal (xp only found in "start, programs, accessories, Communications"
¦Tftpd32.303
¦Emergeny.ub
¦Original_1.06_Notfallimage
¦Bootable usb stick with fat32 formatted
Procedure:
1 = Download files, "tftpd32.zip" unpack to "c:emergency"
2 = The file "emergency.ub" to "c: emergency" copy
3 = Unpack "Original_1.06_Notfallimage" to USB STICK "?:/kathrein/ufs910" = 6 x.Img files.
5 = connect kathi directly with your pc / laptop via crossovercable
6 = on PC go to , control panel/ network connections/ & right click local area connection & select properties.
7 = find "internet protocol(TCP/IP)" click on it then select properties
8 = click Use the Following IP address 192.168.1.80
Gateway and dns-server remain EMPTY!
9 = Click "OK" button (reboot maybe required?)
10 = Stop all firewalls and an****rus programs (not just turn off!)
11 = Now also connect kathy via a nullmodemcable to your pc / laptop
12 = Start program tftpd32 (tftpd32.exe)
13= Under server interfaces select "192.168.1.80"
14 = click "browse" and your select folder "c: emergency" and "ok"
15 = Then click "settings" select "browse" and select "c: emergency" and "ok"
16 = leave tftpd32 running
17 = Start Hyperterminal
18 = when The small window opens click "cancel" to close
19 = select FILE / properties
20 = connect using COM1 or whatever your serial port is on
21 = Then select "Configure" button and in the the newly opened window:
Bits per second: 115200
Data Bits: 8
Parity: None
Stop bits: 1
Flow Control: none
22 = click "Ok" to confirm
23 = Hyperterminal is now ready for data exchange with the kathi!
24 = Switch Kathi on by a rear power switch while pressing "enter" button of your pc / laptop repeatedly to pause kathi's
Boot process!
25 = If Done Correctly hyperterminal should a few entries to be seen in the last lines, and the cursor blinks at
"<STB7100-REF>"
(Retry If this Isnt on the screen!)
The following are just typed in at the promt And after each line press "enter" to confirm and wait till erase finishes
followed by next line
erase a0200000 a029ffff (PRESS ENTER)
erase a02a0000 a04dffff (PRESS ENTER)
erase a04e0000 a0adffff (PRESS ENTER)
erase A0C00000 A0ffffff (PRESS ENTER)
26 =When finished switch off box
27 = Switch Kathi on by a rear power switch while pressing "enter" button of your pc / laptop repeatedly to pause kathi's
Boot process!
28 = If Done Correctly hyperterminal should a few entries to be seen in the last lines, and the cursor blinks at
"<STB7100-REF>"
(Retry If this Isnt on the screen!)
29 = Type these into hyperterminal again one line at a time following by (enter)
Set ipaddr 192.168.1.20 (press enter)
Set serverip 192.168.1.80 (press enter)
TFTP a4000000 emergency.ub (press enter)
30 = If everything worked hyperterminal will show "loading:
########…" And at the end "done", You should have lots of "#" and no "T"
31 = Plug Usb stick in the front usb port.
32 = Hyperterminal the following followed by (enter)
Bootm a4000000
33 = Kathi should display "update"(Lasts approximately 5-6 Min.)
34 = Close Hyperterminal & tftpd
35 = After successful flashing Remove usb-stick.
Now you have Original 1.06 Image.